The slow color changes of this yarn and the log cabin construction technique contribute interest to the final look of this felted tote. The bag is constructed by knitting two log cabin squares from self-striping yarn and joining them together while creating the sides, bottom, and strap of the bag. There is no seaming and minimal finishing required.
Materials
Needle size: US 10½ / 6.5 mm (or size needed to obtain gauge)
Yarn: Noro Kureyon , colorway 150, 5 skeins (550 yards)
Tapestry Needle
Stitch markers
Safety pin or removable stitch marker
Gauge: 3.5 stitches per inch in garter stitch, prior to felting
Dimensions: about 18” by 16”, plus strap, prior to feltin
Front and Back (make 2)
Cast on 12. Knit 10 garter ridges (20 rows). *Bind off on right side, keeping last stitch on right needle. Rotate 90 degrees clockwise. With right side facing you, pick up one stitch for each garter ridge or bound off stitch. Knit 5 garter ridges.* Repeat from * 11 times, ending with 13 blocks total (center square surrounded by 12 additional blocks). Bind off all stitches on right side.
Strap and sides
At this point you will be joining the front and back pieces together while creating the sides and bottom of the bag. This is accomplished by picking up stitches from the front and back pieces at the end of each row of the side piece and knitting them together with the side stitches. This might be a little awkward for the first inch or two, but very soon the side of the bag will have enough structure to make it easier to handle. The sides of the bag widen slightly toward the bottom.
Setup row: Arrange front and back pieces with wrong sides together. With right side facing, pick up one stitch in corner of front piece (as if you were going to begin another log cabin strip). Using backward loop method, cast on 2, place marker, cast on 1, place marker, cast on 3. Pick up one stitch from corner of back piece. Turn.
Side Row: Knit first two stitches together (picked up stitch from previous row and first strap piece). Knit to end. Pick up one stitch from the next garter ridge or bound off stitch at the edge of the adjacent front/back piece.
Repeat side row 10 times.
Increase row: Knit first two stitches together (picked up stitch from previous row and first strap piece). Knit to stitch before first marker, kfb, k1, kfb. Knit to end. Pick up one stitch from the next garter ridge or bound off stitch at the edge of the adjacent front/back piece.
Repeat side row 15 times.
Repeat increase row.
Repeat side row 19 times.
Repeat increase row.
Repeat side row 19 times.
Repeat increase row. This is the last increase row. To mark the point on the opposite side of the body of the bag where decreases need to begin, trace a straight line across the work to the opposite edge and place a safety pin or removable marker at that spot.
Work side rows for the remainder of the side of the bag. When you reach the corner of the piece, just keep going - continue around the corner by picking up the first garter ridge/bound off stitch from the bottom edge. Continue side row for the bottom of the bag and second side of the piece until you reach your pin/removable marker.
Decrease row: Knit first two stitches together (picked up stitch from previous row and first strap piece). Knit to stitch before first marker, ssk, k1, k2tog. Knit to end. Pick up one stitch from the next garter ridge or bound off stitch at the edge of the adjacent front/back piece.
Repeat side row 19 times.
Repeat decrease row.
Repeat side row 19 times.
Repeat decrease row.
Repeat side row 15 times.
Repeat decrease row.
Work side row for the remainder of this side of the bag, which should be about 11 rows.
When you reach the top corner of the piece, knit back and forth on the remaining 7 stitches until strap is about 28 inches long. Bind off all stitches.
Finishing
Sew strap end to cast on row of side. Weave in ends. The felting process is pretty forgiving here, so don’t sweat imperfect finishing, but make sure that all ends are secure enough not to unravel during felting.
Felt. There are many, many felting tips and tutorials online. I usually toss my item in a pillowcase or laundry bag and put it through a short hot wash with a bit of detergent and a few pairs of jeans, checking it frequently and stopping before the spin cycle.
Block to the shape you want and allow to dry completely.
